Polymer Nanocomposites Based on Nanosized Substituted Ferrites (NiZn)1-xMnxFe2O4 on the Surface of Carbon Nanotubes for Effective Interaction with High-Frequency EM Radiation.

To create materials that interact effectively with electromagnetic (EM) radiation, new nanosized substituted ferrites (NiZn)1-xMnxFe2O4 (x = 0, 0.5, and 1) anchored on the surface of multi-walled carbon nanotubes (CNTs) have been synthesized. The concentration of CNTs in the (NiZn)1-xMnxFe2O4/CNT system was from 0.05 to 0.07 vol. fractions. The dielectric and magnetic characteristics of both pristine (NiZn)1-xMnxFe2O4 ferrites and (NiZn)1-xMnxFe2O4/CNT composite systems were studied. The introduction of (NiZn)1-xMnxFe2O4/CNT composites into the amorphous epoxy matrix allows to tailor absorbing properties at the high-frequency by effectively shifting the maximum peak values of the absorption and reflection coefficient to a region of lower frequencies (20-30 GHz). The microwave adsorption properties of (NiZn)1-xMnxFe2O4/0.07CNT-ER (x = 0.5) systems showed that the maximum absorption bandwidth with reflection loss below -10 dB is about 11 GHz.

Polyimide/Ionic Liquid Composite Membranes for Middle and High Temperature Fuel Cell Application: Water Sorption Behavior and Proton Conductivity.

Four water insoluble room-temperature protic ionic liquids (PILs) based on the N-alkylimidazolium cation with the alkyl chain length from 1 to 4 and bis(trifluoromethylsulfonyl)imide anion were synthesized and their chemical structure was confirmed by the 1H NMR and 19F NMR analysis. PILs were revealed to be thermally stable up to 360 and 400 °C. At the same time, the proton conductivity of PILs was found to be dependent mostly on the temperature and, to a less extent, on the type of the cation, i.e., the increase of the conductivity from ~3 × 10-4 S/cm at 25 °C to 2 × 10-2 S/cm at 150 °C was observed. The water vapour sorption capacity of PILs was evaluated as a function of relative humidity and the influence of the alkyl chain length on the phase behaviour in the PIL-water system was discussed. The composite polyimide/PILs membranes were prepared by the PIL immobilization in the porous polymer (Matrimid® 5218) film. The composite membranes showed a high level of proton conductivity (~10-3 S/cm) at elevated temperatures (up to 160 °C). The obtained results reveal that the elaborated composite polyimide/PIL membranes are promising candidates for the application as proton exchange membrane at middle and high temperatures.

Antibiofilm Activity of Polyamide 11 Modified with Thermally Stable Polymeric Biocide Polyhexamethylene Guanidine 2-Naphtalenesulfonate.

The choice of efficient antimicrobial additives for polyamide resins is very difficult because of their high processing temperatures of up to 300 °C. In this study, a new, thermally stable polymeric biocide, polyhexamethylene guanidine 2-naphtalenesulfonate (PHMG-NS), was synthesised. According to thermogravimetric analysis, PHMG-NS has a thermal degradation point of 357 °C, confirming its potential use in joint melt processing with polyamide resins. Polyamide 11 (PA-11) films containing 5, 7 and 10 wt% of PHMG-NS were prepared by compression molding and subsequently characterised by FTIR spectroscopy. The surface properties were evaluated both by contact angle, and contactless induction. The incorporation of 10 wt% of PHMG-NS into PA-11 films was found to increase the positive surface charge density by almost two orders of magnitude. PA-11/PHMG-NS composites were found to have a thermal decomposition point at about 400 °C. Mechanical testing showed no change of the tensile strength of polyamide films containing PHMG-NS up to 7 wt%. Antibiofilm activity against the opportunistic bacteria Staphylococcus aureus and Escherichia coli was demonstrated for films containing 7 or 10 wt% of PHMG-NS, through a local biocide effect possibly based on an influence on the bacterial eDNA. The biocide hardly leached from the PA-11 matrix into water, at a rate of less than 1% from its total content for 21 days.